What's special about this 4:1 Heat Shrink Tubing?
- Shrinks down to 25% of its original diameter; also shrinks 14% or less in its axial direction (lengthwise).
- Dual Wall tubing creates a watertight seal to protect wire, cable and connector components.
- Sold by the foot, so you don't have to purchase more than you need.
- Available in Black
- Click for More Features
|4:1 Adhesive Lined Heat Shrink Tube|
||W4A0.19-4FT||4:1 Adhesive Lined Heat Shrink Tube, 3/16", 4Ft|
||W4A0.31-4FT||4:1 Adhesive Lined Heat Shrink Tube, 5/16", 4ft|
||W4A0.50-4FT||4:1 Adhesive Lined Heat Shrink Tube, 1/2", 4Ft|
||W4A0.75-4FT||4:1 Adhesive Lined Heat Shrink Tube, 3/4", 4Ft|
||W4A1.00-4FT||4:1 Adhesive Lined Heat Shrink Tube, 1", 4Ft|
||W4A1.25-4FT||4:1 Adhesive Lined Heat Shrink Tube, 1 1/4", 4Ft|
||W4A2.00-4FT||4:1 Adhesive Lined Heat Shrink Tube, 2", 4Ft|
4 foot sections are the maximum continuous length on Dual Wall and Specialty Tubing
Click here for 4:1 Adhesive Lined Tubing (Dual Wall) specifications
Our 4:1 over-expanded polyolefin heat shrink tubing is flexible, flame-retardant and used for specialty applications that include cable jacket retrofitting and repair, as well as the electrical insulation of wire assemblies with oversized components or connectors. The over-expanded product fits easily over the end of a connector, and shrinks down to 25% of its original diameter to fit snugly over both the connector and any narrower attached wires. Available in Black, and sold by the foot.
Adhesive-Lined Heat Shrink
The adhesive version of our 4:1 heat shrink features “dual-wall” design, which is made up of an outer polyolefin (heat shrink) tube lined with an interior coating of heat-activated adhesive. During application, as the outer tubing shrinks, the inner layer melts, flows, and then resets when cooled, helping the tubing to achieve a snug, moisture-resistant fit around wire harnesses, cables and connectors. We recommend it for applications that require strain relief and watertight seals.
|Tensile Strength (psi)||ASTM D 638||1500 min.|
|Elongation (%)||ASTM D 638||200 min.|
|Specific Gravity||ASTM D 792||1.35 max.|
|Low Temperature Flexibility -55°C||MIL-DTL-23053||no cracking|
|Heat Shock 4 hours at 250°C||MIL-DTL-23053||no cracking|
|Heat Resistance (175°C, 168 hrs.)
|ASTM D638||100 min.|
|Secant Modulus (psi)||ASTM D 882||2.5 x 10,000 max.|
|Longitudinal Change (%)||MIL-DTL-23053||±5|
|Dielectric Strength||ASTM D 876||500 min.|
|Volume Resistivity||ASTM D 876||1.0 x 10,000 min.|
|Corrosion (175°C, 16hrs)||MIL-DTL-23053||no corrosion|
|Water Absorption (%)||ASTM D 570||0.5 max.|
|Fluid Resistance (23°C, 24 hrs.)
Tensile Strength (psi)
|Flammability||UL 224 VW-1||
|Shrink Temperature, Nominal||--||90°C|
|Application (Typical)||General Purpose Over Expanded|
|Continuous Operating Temperature||-55 to 135°C|
|UL Rating & File No. (Subject 224)||125°C, 600V
VW-1 (Jacket only for dual wall)
|UL Catalog No.||826 Suffix 3X|
MIL-I-23053/5 Class 1 and Class 3. MIL-R-46846, Type V
UL 224 125°C, 600 V, VW-1 File E48762 YDPU2
LG heat shrinkable and non-shrinkable tubing products do not contain the compound Di (2-ethylhexyl) phthalate commonly referred to as DEHP.
In addition, LG heat shrinkable and non-shrinkable tubing products do not contain PFOS (perfluoroctane sulfonate), PFOA (perfluorocanoic acid) or Tinuvin 320.
4:1 Adhesive Heat Shrink Tubing
Minimum Shrink Temperature: 90°C
|MINIMUM ID||MAXIMUM ID||MINIMUM TOTAL WALL THICKNESS
|MINIMUM WALL THICKNESS
*Metric sizes available for special orders.
Limiting Oxygen Index (LOI)
The ratio of how much oxygen - as compared to other gases - needs to be present in the air surrounding a particular material in order for that material to burn. The fact that Earth's normal atmospheric air contains around 21% oxygen is used a reference point when materials are classified into burn categories that are based on Limiting Oxygen Index. Substances that are combustible in air containing less than 21% oxygen are considered flammable, while those that burn in the range of anything greater than 21% but less than 28% are typically labeled "slow burning". Any material with an LOI that exceeds 28% is classified as self-extinguishing.
In the table below, you'll find a list of polymers commonly found in our heat shrink tubing and braided sleeving products, along with their LOIs and the burn categories each falls into.
|ECTFE (Ethylene chlorotrifluoroethylene)||Halar||64%||Self Extinguishing|
|Nylon 6:6||N/A||Ranges fron 24-29%||Slow Burning to Self Extinguishing|
|PET (Polyethylene Terephthalate)||Mylar (film), Dacron (fiber)||Ranges from 21-34%||Slow Burning to Self Extinguishing|
|Polypropylene (PP)||polythene (in the UK)||17%||Flammable|
|Polytetrafluoroethylene (PTFE)||Teflon||95%||Self Extinguishing|
|Polyvinyl Chloride (PVC)||N/A||Ranges from 45-49%||Self Extinguishing|
Request A Quote
Did you know that we can give you a quote for most of our products, including shipping?
You can also call us toll free 1-833-3CABLEORG (1-833-322-2536)
Questions & Answers
Do you have any questions about this product?
Let our experts and customers resolve all your doubts