Kwikpath Optical Fiber & Communication Cable Raceway Accessories
Kwikpath Fittings reduce the need for pulling long runs of raceway around awkward twists and turns and tight spaces. The various connections and innovative y-coupler allow you to easily branch off raceway into different directions with out removing existing cabling. They make the communications raceway easy to handle and install and are a great labor savings.
IPEX Scissor Knife Cutting Tool
Seal End Plugs
SCEPTER® CONDUIT CLAMPS & SPACERS
Kwikpath RESI RISER STRAPS
KWIKPATH MEETS ALL BUILDING REGULATIONS
Eliminate all building compliance concerns and pass inspection knowing every part of your fittings and raceway system 100% meets all UL, NEC, NFPA, and EIA/TIA requirements.
EIA/TIA – Meets all commercial building telecommunications cable protection and performance codes.
NEC 2005 (National Electric Code) governs the removal of abandoned cables in air handling spaces, Kwikpath is in compliance with articles 770 and 800 with its convenient way to remove and replace cable through the Kwikpath raceway.
NFPA- (National Fire protection Association) meets all cable management requirements for air plenums, ducts and other environmental air spaces.
UL2024 General Purpose-certified to meet standards for flame damage and flame test.
PLEASE NOTE: These products ship in 1 week
There is a 25% restock fee for returns
|KP-CLC20||Cutting Tool 1/2" - 1"||0.3 lb|
|KP-CLC35||Cutting Tool 1/2" - 2"||0.3 lb|
|KP-SSB||Replacement Blade for KP-CLC20||1 lb|
|KP-SB35||Replacement Blade for KP-CLC35||1 lb|
Seal End Plugs
|KP-SEP075||3/4"||50 per pack|
|KP-SEP100||1"||50 per pack|
|KP-SEP125||1-1/4"||50 per pack|
|KP-SEP150||1-1/2"||50 per pack|
|KP-SEP200||2"||50 per pack|
Clamp & Spacer
|KP-CCS10||1/2"||100 per pack|
|KP-CCS15||3/4"||70 per pack|
|KP-CCS20||1"||50 per pack|
|KP-CCS25||1-1/4"||30 per pack|
|KP-CCS30||1-1/2"||25 per pack|
|KP-CCS35||2"||20 per pack|
|KP-PY075-200||3/4" - 2"||10 per pack|
Riser & Resi Straps
|KP-S075||3/4"||400 per pack|
|KP-S100||1"||500 per pack|
|KP-S125||1-1/4"||400 per pack|
|KP-S150||1-1/2"||225 per pack|
|KP-S200||2"||200 per pack|
- Kwikpath Technical Guide (PDF)
- Kwikpath Brochure (PDF)
- View Y-Coupler Specs and Installation Info (PDF)
- View Clamps & Spacers Specs (PDF)
Installing Kwikpath is Easy
1. UNROLL KWIKPATH TO DESIRED LENGTH
Available in convenient coil lengths of 200 ft. and reel lengths up to 1000 ft., Kwikpath gives you the flexibility to measure out end-to-end home-run systems with fewer couplings. Convenient lightweight coil lengths are easy to handle and disposable reels ensure you don’t have to store and return large steel reels.
2. CUT KWIKPATH WITH AN IPEX CUTTER
For straight cuts every time, use our scissor-style cutting tool. However, no special tools or cutting equipment are required.You can even cut Kwikpath with a regular utility knife.
3. MAKE BENDS AND TURNS BY HAND
Kwikpath is so lightweight and flexible you can bend, turn and manipulate it by hand to install it easily around irregular curves and in tight spaces.This flexibility allows you to get the job done right the first time, reducing wasted material and time.
4. SIMPLY SNAP CONNECTIONS TOGETHER
Kwikpath’s unique snap-on fittings make terminating or coupling quick and easy, and six locking tabs ensure the fittings stay connected. No messy cementing or screws to tighten.
5. PULL CABLE THROUGH KWIKPATH
Kwikpath’s interior corrugated surface reduces pull-forces and friction, so pulling wires through the tubing is considerably easier than through metal tubing. And you can pull cables through longer raceways without worrying about damage to the cables.
Reviewed by 1 customer
Displaying review 1
- Easily Expanded
- Easy To Set Up
- Highly Compatible
- Highly Secure Networks
- High Volume
- Home Networks
- Small Offices
Comments about Kwikpath Cutting Tool 1/2"-1":
In the past it was difficult to branch out from a raceway to another workstation. The Y-coupler makes it quick, simple and professional to add cables in a raceway from an existing raceway duct.
- Primary use: