UG512 UltraGlider 12V Assembly without Applicators

Safer, More Efficient, and Applies Lube More Evenly Than Can Be Done By Hand


Greenlee UG512

Close Window

UG512 UltraGlider 12V Assembly without Applicators

    Additional Images
  • UG512 UltraGlider - icon
  • Greenlee UG512 charging port- icon
  • Greenlee UG512 - icon

This requires one or more of the following: javascript enabled, Flash Video Player, and Quicktime or Windows Media Player
Copyright ©2017

Low Price GuaranteeWhat's special about this UltraGlider?

  • Basic system without applicators
  • Do three to four buckets with one battery charge
  • Neat and easy application of lubricants
  • Includes pump unit, battery unit, and hose
  • Click for More Features

The Greenlee UG5 Ultra GLIDER™ is the “new way” to effectively apply cable lube during cable installation. The Ultra GLIDER™ has several advantages over the manual method used by most contractors today. The UG5 saves labor time - in many cases one person can be eliminated during the job because the same person who controls the feeding of the cable can also control the cable lube application. Cable pulling force is reduced by up to 50% because the lube is applied consistently. It also saves lube cost because it applies lube consistently in a controlled manner.

Pump Unit 39" H x 18" W x 17" D
[1 m x 0.45 m x 0.43 m]
Wheel Diameter 8" [20cm]
Hose Length 10' [3m]
Battery (12V Unit only) - Type Sealed lead acid rechargeable batter, DC output 12-Volt
Battery Life Three to four 5-gallon buckets per charge
Warranty One year
GL-UG512 UltraGlider 12V Assembly without Applicators 71.0 lbs DISCONTINUED





How to Set up the Pump

Step: 1
Place a 5 gallon bucket of lubricant into the dolly and remove the lid from the bucket.
Step: 2
setting the platePlace the Follower Plate inside the bucket, setting it on top of the lubricant with the hub facing up, and press down to remove any air pockets.

Step 3:
Place the pump assembly on top of the bucket, and slide the suction pipe through the center hole in the follow plate.

applying the pump    connecting the pump

Step 4:
Plug in the power cord:

  • UG511: Plug the power cord into a grounded outlet.
  • UG512: Plug the power cord into the battery port.

assembled pump

Step 5:
Attach a lubricant applicator to the end of the hose (An applicator must be attached to the hose or lubricant will not flow). Refer to Applicators for UG5 Cable Lubrication System for details on attaching applicators.

Step 6:
Press the medium speed button on the top of the pump unit and then step on the foot switch to start pumping. The pump may take 30 to 60 seconds to build up pressure and pump lubricant out of the collet.



greenlee ez fish tape EZ Fish Tape - Greenlee
Flat steel tape reaches easily above ceilings, under carpets, and through walls to install wire. 25' (7.6 m) long, extending your reach where a traditional fish tape can't.
Cable CasterCable Caster - Greenlee
Improves productivity when installing cables over large distances. Just shoot the glow-in-the-dark green dart up to 50 feet, attach your cable and pull it back using the take-up reel. An integrated flashlight holder will accommodate the Pocket flashlight for improved visibility in dark areas.
Clear LubeClear Lube- Greenlee
Designed for use within electrical or datacom cable pulls. Clear and colorless for quick, easy clean-up. Excellent lubricity for fast pulls (.27-.29 COF).
Clear LubeClear Lube Pulling Lubricant, 5 gallon - Greenlee
Excellent for use in electrical or datacom cable applications; Easy to use and clean up, clear and colorless; Safe for use anywhere, non-hazardous, non-toxic and non-corrosive; Well lubricated for fast pulls 9.27-.29 COF).

What can make this page better?

We do everything we can think of to provide you with the product specs, images and ordering info you need, but if we're missing something or still have room to improve, please let us know. Your comments, suggestions and questions are the best tools we have for serving you better!