UG511S UltraGlider 120V Including Slip-In Applicator Kit UGSAK

Safer, More Efficient and Applies Lub More Evenly Than Can Be Done By Hand


Greenlee UG511S

Close Window

UG511S UltraGlider 120V Including Slip-In Applicator Kit UGSAK

    Additional Images
  • Greenlee UG511S - icon
  • Greenlee UtraGlider 120V - icon
  • Cable Pulling Lubricants - icon

This requires one or more of the following: javascript enabled, Flash Video Player, and Quicktime or Windows Media Player
Copyright ©2017

Low Price GuaranteeWhat's special about this UltraGlider?

  • More even application of lubricant then can be done by hand
  • System includes: pump unit, UGSAK Slip-In Applicator Kit, hose
  • Reduces mess associated with manual application of lubricants
  • Click for More Features

The Greenlee UG5 Ultra GLIDER™ is the “new way” to effectively apply cable lube during cable installation. The Ultra GLIDER™ has several advantages over the manual method used by most contractors today. The UG5 saves labor time - in many cases one person can be eliminated during the job because the same person who controls the feeding of the cable can also control the cable lube application. Cable pulling force is reduced by up to 50% because the lube is applied consistently. It also saves lube cost because it applies lube consistently in a controlled manner.

Pump Unit 39" H x 18" W x 17" D
[1 m x 0.45 m x 0.43 m]
Wheel Diameter 8" [20cm]
Hose Length 10' [3m]
Motor AC output: 120-volt
Amps: 6 amps
Warranty One year
GL-UG511S UltraGlider 120V Including Slip-In Applicator Kit (UGSAK) 68.5 lbs DISCONTINUED



How to Set up the Pump

Step: 1
Place a 5 gallon bucket of lubricant into the dolly and remove the lid from the bucket.
Step: 2
setting the platePlace the Follower Plate inside the bucket, setting it on top of the lubricant with the hub facing up, and press down to remove any air pockets.

Step 3:
Place the pump assembly on top of the bucket, and slide the suction pipe through the center hole in the follow plate.

applying the pump    connecting the pump

Step 4:
Plug in the power cord:

  • UG511: Plug the power cord into a grounded outlet.
  • UG512: Plug the power cord into the battery port.

assembled pump

Step 5:
Attach a lubricant applicator to the end of the hose (An applicator must be attached to the hose or lubricant will not flow). Refer to Applicators for UG5 Cable Lubrication System for details on attaching applicators.

Step 6:
Press the medium speed button on the top of the pump unit and then step on the foot switch to start pumping. The pump may take 30 to 60 seconds to build up pressure and pump lubricant out of the collet.



greenlee ez fish tape EZ Fish Tape - Greenlee
Flat steel tape reaches easily above ceilings, under carpets, and through walls to install wire. 25' (7.6 m) long, extending your reach where a traditional fish tape can't.
Cable CasterCable Caster - Greenlee
Improves productivity when installing cables over large distances. Just shoot the glow-in-the-dark green dart up to 50 feet, attach your cable and pull it back using the take-up reel. An integrated flashlight holder will accommodate the Pocket flashlight for improved visibility in dark areas.
Clear LubeClear Lube- Greenlee
Designed for use within electrical or datacom cable pulls. Clear and colorless for quick, easy clean-up. Excellent lubricity for fast pulls (.27-.29 COF).
Clear LubeClear Lube Pulling Lubricant, 5 gallon - Greenlee
Excellent for use in electrical or datacom cable applications; Easy to use and clean up, clear and colorless; Safe for use anywhere, non-hazardous, non-toxic and non-corrosive; Well lubricated for fast pulls 9.27-.29 COF).

What can make this page better?

We do everything we can think of to provide you with the product specs, images and ordering info you need, but if we're missing something or still have room to improve, please let us know. Your comments, suggestions and questions are the best tools we have for serving you better!