Mitigators 50Hz and 60Hz
Technical Specifications and Functions

GENERAL SPECIFICATIONS 60Hz MODEL 50Hz MODEL
LCD Frequency:
Display Range (Low Zoom):
Resolution (Zoom Mode):
Low:
Medium:
High:

20Hz to 4080Hz

36Hz
12Hz
1Hz

20Hz to 3400Hz

30Hz
10Hz
1Hz
Zoom Mode Window Ranges:
Low:
Medium:
High:

4068Hz
1404Hz
117Hz

3380Hz
1150Hz
117Hz
Weighting (Filters): C-Message,
3KHz Flat, 20/F
Psophometer, 3KHz Flat (C.C.I.T.T.),
None, 1/F
Max. Input Levels:
Across Tip & Ring:
Tip-Ring to Ground:

24VAC & 200VDC
200VAC & 200VDC

24VAC & 200VDC
200VAC & 200VDC
The following specs are common on
the 60Hz and 50Hz Models
Noise Measurement Mode Range:
Power Influence:
Circuit Noise:
Circuit Loss:

20 fi 140 dBrn
0 fi 120 dBrn
-90 fi 30 dBm
 
Noise Measurement Mode Accuracy: ± .5dB  
Spectrum Mode Range: 0 fi 120 dBrn Line/Cir
20 fi 140 dBrn Line/PIF
 
Spectrum Mode Level Accuracy: ±1dB
Spectrum Mode Frequency Accuracy:
Update Time (Spectrum):
Update Time (Geiger):
Harmonic Current Probe Range:
Harmonic Current Probe Resolution:
0 to 30 Amps:
30 to 100 Amps:

±1Hz
7.5 seconds
2 seconds
0 - 10A, 0 - 100A
0.01 Amps
0.1 Amps
 
LCD on Screen Display Range:
Input Impedances:
90dB
600Ω, 900Ω,
Bridging (600Ω or 900Ω)
 
Hold Circuit:
Battery Life (rechargeable):
Electronic
2 Hours Typical
 
Physical Specifications
Dimensions:
Display Size:
Weight:
10.75" L x 9.75" W x 5" D
4.9" L x 2.5" H
Approximately 10 pounds
 

 

 

Functions Description

"Smokestack" LCD Readout
While in the Spectrum Mode, the LCD screen produces a "smokestack" display of vertical bars that detail the level and frequency of the harmonic noise present in the measured signal. This type of display is ideal for examining the harmonic noise commonly associated with energy radiated from the power lines of an electric utility. The LCD screen also displays other pertinent measurements, such as; Circuit Loss, Circuit Noise and Power Influence. 600 Ohm, 900 Ohm and bridging input impedances are also provided as well as selectable weighting (C-Message, 3KHz Flat & 20/F) or [Psophometer, 3KHz Flat (C.C.I.T.T.), 1/F & None].

Peak Finder
This feature enables you to move from one spectral peak to another, either in the left or right direction. This eliminates having to scroll through each and every spectral measurement just to view peaks.

"Green Window" Test

Sometimes referred to as the "Probe Wire Test", the Green Window Test is a function that enables you to gather useful information about the power line in a very simple manner. Once the power line height is entered, The Mitigator will automatically measure and compute the Ground Return I T, C-Message [PMSG] noise per mile [KM] and 60Hz [50Hz] voltage per mile [KM].

Data Logging
This feature enables you to save data over a specified amount of time at specified intervals using the internal, real-time clock. The data is stored in non-volatile memory which can be recalled and displayed on the LCD screen or printed out via the RS- 232 Port and external serial printer.


Geiger Mode
The "GEIGER" mode allows you to select a function that acts like a Geiger counter. In this mode, The Mitigator can be used to search for the source of user-definable noise. A beeper in The Mitigator beeps faster as the source of noise increases in level. When used in conjunction with a loop coil, this function allows you to employ a "search-and-find" technique for locating the noise source. The beeper allows you to search for the noise without looking at the front panel. This is particularly helpful in situations when you are searching for a noise source while operating a motor vehicle.

Zoom Mode
In the "ZOOM" mode, the LCD screen can "zoom in" on an offending frequency, enlarge it on the screen, and display it along with adjacent frequencies on either side of it. There are three levels in the "ZOOM" Mode: Low, Medium and High.

Analysis Mode
The "ANALYSIS" Mode is a sub-feature of the Spectrum Mode. The Analysis Mode uses data gathered in the Spectrum Mode and enters that data into a probability matrix containing common problems that relate to power lines. The problems are then displayed in order of highest probability.

Three-Way Power Operation
The Mitigator can be powered by three different methods: an AC Power Pack, an internal rechargeable battery and a 12 volt vehicle system (cigarette lighter). Standard household current (120Vac) [47 to 63Hz, 218 to 264Vac] will power the unit through the AC Power Pack and also recharge the internal battery which will operate the unit for approximately 2 hours on a full charge. The internal battery can be completely recharged overnight. A unique topology also allows the internal battery to recharge from a 12 volt vehicle system. All three interfaces are included with The Mitigator.

Serial Printer RS-232 Port
With the use of an external serial printer and the RS-232 Port, you can produce a customized, detailed hardcopy analysis of all tests previously saved in the unit's non-volatile memory. This hardcopy documents your measurements and can serve as a basis for helping to solve the noise problem at its origin.

Harmonic Current Probe Input
When used with the optional Triplett Harmonic Current Probes (Model HC-10 and Model HC-100), The Mitigator will display Amps in either a spectral or an RMS format. The HC-10 allows measurements up to 10 Amps while the HC-100 allows measurements up to 100 Amps. This feature is particularly useful for evaluating telephone cable sheath current and for tuning Harmonic Suppression Reactors (HSR).

What can make this page better?

We do everything we can think of to provide you with the product specs, images and ordering info you need, but if we’re missing something or still have room to improve, please let us know. Your comments, suggestions and questions are the best tools we have for serving you better!